Fenix3 英文测试版固件更新 6.19

  • A+
所属分类:固件更新

Fenix3升级、固件更新、刷机教程:

【图文】刷Fenix3 Beta版固件教程,仅限英文版

Fenix3英文测试版固件 全系列下载地址:

百度云盘提取密码:87kn

更新日志

Changes made from version 6.15 to 6.19:

  • Added support for Advanced Running Dynamics. These include: Ground Contact Time Balance, Stride Length and Vertical Ratio (Requires HRM-Run v.6.60, HRM-Tri v. 4.20)
  • Improved reliability of altitude during activities
  • Fixed potential issue with auto lap during workouts
  • Fixed potential issue with the location field layout for certain position formats
  • Fixed potential issues with battery discharge beyond the typical rate when Bluetooth is turned off
  • Fixed potential issue reconnecting to ANT+ sensors

 

Changes made from version 6.14 to 6.15:

  • Added support for viewing altitude on the watch face. Note: This requires Display update v2.91, see installation instructions below.
  • Further improvements to altimeter and barometer accuracy in watch mode (when not  performing a GPS activity). Note: Settings > Sensors > Altimeter > Calibrate or press START from the Altimeter widget to calibrate the Altimeter to a known altitude.
  • Improved reliability of Bluetooth manual syncs for certain use cases.
  • Fixed potential issues with altitude inaccuracies at low speeds during a GPS activity.
  • Fixed a potential issue where the button lock banner could prevent viewing of smart notifications.
  • Fixed a potential issue with Wi-Fi syncs.
  • Fixed a potential issue with VO2 Max when the Foot Pod Speed setting was set to 'Always'.
  • Fixed a potential issue where activity files with HR data would fail to upload.

 

Changes made from version 6.12 to 6.14:

  • Fixed an issue where user's alerts would get corrupted when upgrading software. Note: Any alert created after 6.01 will be removed and will need to be added again.
  • Fixed a potential issue where the watch would randomly reboot, while playing a vibration.
  • Fixed a potential issue with setting up the crank length for non Vector power meters.

 

Changes made from version 6.11 to 6.12:

  • Fix for foot pod dropping as speed source

 

Changes made from version 6.09 to 6.11:

  • Added support for Connect IQ SDK 1.2.1.
  • Further improvements for consistency and accuracy of altimeter auto calibration (performed during a GPS activity).
  • Improved activity tracking step calculation accuracy for certain use cases.
  • Fixed an issue where key presses would not work, if a low battery notification was received when the unit was locked.
  • Due to intermittent reliability issues, reverted pool swim algorithm changes to those found in the current public release (4.90).

 

Changes made from version 6.08 to 6.09:

  • Improved consistency and accuracy of altimeter auto calibration (performed during a GPS activity). Notes: GPS and manual calibration points will be used to determine the best overall calibration possible. A secondary step when acquiring a GPS fix at activity start will help denote a more accurate fix for altitude purposes (yellow to green ring indication). Settings > Sensors > Altimeter > Auto Cal. is now an On/Off setting as the 'Once' and 'Continuous' settings are no longer necessary. Use Settings > Sensors > Altimeter > Calibrate to calibrate the Altimeter to a known altitude.
  • Further improvements to altimeter and barometer accuracy in watch mode (when not performing a GPS activity). Note: Settings > Sensors > Altimeter > Calibrate or press START from the Altimeter widget to calibrate the Altimeter to a known altitude.
  • Fixed potential issue with manual altimeter calibration during a GPS activity.
  • Fixed issue with tempe connectivity.

 

Changes made from version 6.06 to 6.08:

  • Improved altimeter and barometer accuracy in watch mode (when not performing a GPS activity). Note: use Settings > Sensors > Altimeter > Calibrate or press START from the Altimeter widget to calibrate the Altimeter to a known altitude.
  • Improved vibration profiles to be differentiated based on alert type.
  • Improved reliability of 'Weather' widget on iOS.
  • Fixed a potential issue with exiting the 'Find Phone' app.
  • Fixed a potential issue with storm alerts not working in certain use cases.

 

Changes made from version 6.05 to 6.06:

  • Added support for Connect IQ SDK 1.2.0.
  • Fixed a potential issue with Footpod being incorrectly used as the source for distance accrual.

 

Notes:

  • For any issues that you encounter, please include [Device s/w version, Issue, Steps to Reproduce, Did this issue exist in the last stable s/w version, Any additional details related to the reported issue] and email to fenix3.beta@garmin.com. Please note that you may not get a response to the email, unless we need more information on the issue you report.
  • Although this software is believed to be reliable, it has not yet been released for production and should be used at your own risk.

 

 

 

文件下载

广告也精彩
  • 微信:Mingtel
  • 微信二维码名片
  • weinxin
  • 支付宝搜索:512000173
  • 充值可抵扣,最多领38元!
  • weinxin
明
佳明开发者 | www.garmindev.cn

发表评论

您必须才能发表评论!

目前评论:1   其中:访客  1   博主  0

    • 4klover 4klover 7

      英文版就是更新快